48V 200Ah 고출력 배터리로 전기차 고속충전소 지원 가능

ㅏ single 48V 200Ah 배터리 cannot directly support an EV fast-charging station. 하지만, multiple 48V 200Ah batteries can be used to create a Battery Energy Storage System (베스). 이 BESS는 전력망과 충전소 사이의 완충 역할을 할 수 있습니다.. This setup is known as battery-buffered DC fast charging.

Power Requirements for Fast Charging

EV fast-charging stations, also known as Level 3 or DC fast chargers, provide a high-power direct current (DC) directly to an EV’s battery, bypassing the vehicle’s onboard charger. This is what allows for a rapid charge. These chargers operate at much higher power outputs than a typical 48V battery can provide.

• Fast Charging Power: DC fast chargers for passenger vehicles typically have power outputs ranging from 50 kW to 350 kW or even higher.
• The 48V 200Ah Battery’s Power: To calculate the maximum continuous power of a 48V 200Ah battery, you multiply the voltage by the continuous discharge current. A typical 48V 200Ah battery for home energy storage or other applications might have a continuous discharge current of 100A to 200A.
  • $피=V\times 나$
  • $피=48V\times 200ㅏ=9.6kW$
  • This is far below the minimum power required for a fast-charging station.

Voltage and Energy Discrepancies

Modern EVs use high-voltage battery systems, often in the range of 400V to 800V, to handle the high power of fast charging efficiently. A 48V battery, 반면에, operates at a significantly lower voltage. While a bank of multiple 48V batteries could be connected in series to increase the voltage, it would still not be practical or efficient for a fast-charging application.

A fast-charging station needs to deliver a large amount of energy in a short time. The energy stored in a single 48V 200Ah battery is calculated as:

• $이자형=V\times ㅏ시간$
• $이자형=48V\times 200ㅏ시간=9,600와트시$ 또는 9.6 kWh

A typical EV battery has a capacity of 60 kWh에 100 kWh or more. This means one 48V 200Ah battery only holds a fraction of the energy needed to fully charge a single EV, let alone serve as the power source for a public charging station.

How a BESS Makes it Possible

Instead of connecting the fast charger directly to a weak power grid connection, the BESS is used as an intermediary. Here’s how it works:

1. Grid Charging: The BESS draws power from the grid at a continuous, low to moderate rate, effectively “sipping” electricity over time. This avoids the need for a costly, high-capacity grid connection.
2. 에너지 저장: The drawn power is stored in the large battery bank, which is a collection of many 48V 200Ah batteries connected in series and parallel to achieve the required voltage and capacity.
3. 고속 충전: When an EV plugs in for a fast charge, the BESS can discharge its stored energy rapidly and at high power, providing the necessary current and voltage to the vehicle. This allows the fast-charging station to operate at its full potential without straining the local grid infrastructure.

Benefits of Battery-Buffered Charging 🔋

Using a BESS with a fast-charging station offers several advantages:

• Grid Infrastructure Savings: It reduces the need for expensive and time-consuming upgrades to the local power grid.
• Peak Shaving: The BESS can be charged during off-peak hours when electricity is cheaper, and then discharge power during on-peak hours to reduce electricity bills for the charging station owner.
• Increased Availability: It enables the deployment of fast chargers in locations with limited grid capacity.
• Demand Charge Management: It helps charging station operators avoid high demand charges from utility companies, which are penalties for sudden, high spikes in electricity usage.

자세한 내용은, please visit: www.hyxinbattery.com